







The Arnett Valve APEX series shears solids on the way closed. The tip cuts through whatever sits in the seat, and the guides hold the gate square. Three pressure classes, one lay length.


| Component | Available materials |
|---|---|
| Body | Carbon steel, SS304, SS316, Duplex, Superduplex, Titanium |
| Knife / gate | SS304, SS316, Duplex, Superduplex, Titanium |
| Shaft and stem | SS304, SS316 |
| Side support | Carbon steel, Superduplex |
| Clevis | Carbon steel, Bronze |
| Seal | NBR, EPDM, FKM Viton |
| Top seal (wiper) | NBR, EPDM, FKM Viton |
| Scraper | PTFE |
Others on request. Ni-Hard wear rings and other special materials are available for extreme duty applications. Epoxy coating on carbon steel components. Body, gate and side supports can also be supplied in 17-4 PH.

Applies across APEX S, APEX H and APEX X.
Higher temperature options available on request.

Hydrostatic testing to API 598, body cavity at 1.5 times design pressure
Quality management to ISO 9001:2015
Pressure Equipment Directive PED 2014/68/EU
Machinery Directive 2006/42/EC
Explosive Atmosphere Directive ATEX 2014/34/EU
| Actuator type | Power source |
|---|---|
| Pneumatic cylinder, double-acting | Compressed air |
| Chain wheel | Manual |
| Electric | Electric |
| Hydraulic cylinder | Hydraulic |
| Handwheel (direct) | Manual |
| Bevel gearbox | Manual |
| Pneumatic cylinder, single-acting | Compressed air |
Actuators interchange on a common ISO 5210 pad with the valve in the line.


The working pressure class of the APEX series.
145 psi across the whole size range, 2” through 42”. The rating holds at every size, so selecting an APEX S stays a one-line decision.
ANSI Class 150 drilling matches the flange class most process lines already carry. APEX S replaces an existing knife gate flange to flange. Flanges, studs and spool length stay exactly as they are.
Shortest overall height of the three variants, from 10.2” at 2” to 48.0” at 24”. Where the line rating sits inside 145 psi, APEX S is the cost-of-ownership pick.
General guided shear duty across the plant, in clean, slurry or acidic media, with a line rating at or below 145 psi and Class 150 flanges.

| NPS | Face-to-face | Overall height | ISO 5210 |
|---|---|---|---|
| 2” | 2.0” | 10.2” | F07 |
| 3” | 2.0” | 12.2” | F07 |
| 4” | 2.0” | 13.4” | F07 |
| 6” | 2.3” | 16.9” | F07 |
| 8” | 2.8” | 20.9” | F10 |
| 10” | 2.8” | 23.4” | F10 |
| 12” | 3.0” | 28.0” | F10 |
| 14” | 3.0” | 31.5” | F10-F14 |
| 16” | 3.5” | 34.8” | F10-F14 |
| 18” | 3.5” | 38.6” | F10-F14 |
| 20” | 4.5” | 41.7” | F14-F16 |
| 24” | 4.5” | 48.0” | F14-F16 |
Custom flange drilling to fit any requirement. Hydrostatic test per API 598, body cavity at 1.5x design pressure. Larger sizes (up to 48”) are available on request.

Same envelope, two and a half times the pressure.
Same face-to-face, same overall height and same ISO 5210 actuator pad as APEX S at every size. Moving up a pressure class leaves the pipework, the actuator and the spool spacing alone.
Drilled for ANSI Class 150 or Class 300, so APEX H bolts straight to whatever the higher-pressure run already carries. Metric drilling available to EN 1092.
Identical internals, seal compounds and packing arrangement to APEX S. Higher pressure service on the same spares list, run by the same crew.
Discharge lines, cyclone feed, higher static head, or any guided shear duty where the line rating passes 145 psi and the maintenance profile stays as it is.

| NPS | Face-to-face | Overall height | ISO 5210 |
|---|---|---|---|
| 2” | 2.0” | 10.2” | F07 |
| 3” | 2.0” | 12.2” | F07 |
| 4” | 2.0” | 13.4” | F07 |
| 6” | 2.3” | 16.9” | F07 |
| 8” | 2.8” | 20.9” | F10 |
| 10” | 2.8” | 23.4” | F10 |
| 12” | 3.0” | 28.0” | F10 |
| 14” | 3.0” | 31.5” | F10-F14 |
| 16” | 3.5” | 34.8” | F10-F14 |
| 18” | 3.5” | 38.6” | F10-F14 |
| 20” | 4.5” | 41.7” | F14-F16 |
| 24” | 4.5” | 48.0” | F14-F16 |
ANSI Class 300 drilling available on APEX H. Consult Arnett. Custom flange drilling to fit any requirement. Hydrostatic test per API 598, body cavity at 1.5x design pressure. Larger sizes (up to 48”) are available on request.

Guided shear at 725 psi.
725 psi across the full size range, 2” to 42”. The heaviest build in the series, and still the same face-to-face at every size. An APEX X drops into the spool an APEX S came out of.
Taller body than APEX S and APEX H, from 1.2” more at 2” to 4.7” at 14”, with a larger ISO 5210 actuator flange from 3” upward, reaching F30 at 20” and 24”.
ANSI Class 300 as standard, with higher classes available on the smaller sizes. The flange platform matches the rating a high-pressure line already carries.
High-head pump discharge, long-distance transport, pressure-let-down circuits, or any guided shear duty above the APEX H ceiling. Consult Arnett for classes above 300.

| NPS | Face-to-face | Overall height | ISO 5210 |
|---|---|---|---|
| 2” | 2.0” | 11.4” | F07 |
| 3” | 2.0” | 14.2” | F07-F10 |
| 4” | 2.0” | 16.1” | F07-F10 |
| 6” | 2.3” | 18.9” | F10 |
| 8” | 2.8” | 23.2” | F14 |
| 10” | 2.8” | 25.8” | F14 |
| 12” | 3.0” | 31.9” | F14 |
| 14” | 3.0” | 36.2” | F16 |
| 16” | 3.5” | 38.6” | F16 |
| 18” | 3.5” | 42.5” | F25 |
| 20” | 4.5” | 46.5” | F30 |
| 24” | 4.5” | 52.4” | F30 |
Higher ANSI classes are available on the smaller sizes. Consult Arnett for class and size combinations. Custom flange drilling to fit any requirement. Hydrostatic test per API 598, body cavity at 1.5x design pressure. Larger sizes (up to 48”) are available on request.

| APEX S | APEX H | APEX X | |
|---|---|---|---|
| Working pressure | 145 psi | 363 psi | 725 psi |
| Sizes | 2” to 42” | 2” to 42” | 2” to 42” |
| Face-to-face | 2” to 10” | 2” to 12” | 2” to 10” |
| Overall height at 24” | 48.0” | 48.0” | 52.4” |
| Flange platform | ANSI Class 150 | ANSI Class 150, Class 300 | ANSI Class 300 and above |
| Shut-off | Bidirectional leakproof | Bidirectional leakproof | Bidirectional leakproof |
Every APEX variant shares one face-to-face dimension. Move up a pressure class and the pipework stays exactly where it is.




Call, send an email or fill in the form. An Arnett engineer replies with a quote and a recommended model.