CORE unidirectional knife gate valves
CORE series

Unidirectional knife gate valves

Max pressure
1450 PSI
Pressure
Max temperature
392°F
Temperature
Sizes
2” - 24”
Sizes
Face-to-face
1.7” - 6.1”
Face-to-face
CORE S series header
Unidirectional knife gate
CORE S valve, series cover
CORE C series header
Extreme pressure knife gate
CORE C valve, series cover

What a replaceable seat does

The Arnett Valve CORE series puts a machined metal seat behind a snap-in soft seat sleeve. The metal holds the geometry and the sleeve holds the seal. When the sleeve reaches the end of its life the site crew changes it with the valve in the line.

Exploded view of the CORE valve
Easy field replaceable soft seatThe sleeve snaps out and in on site. The valve stays where it is.
Metal seat plus soft seatTwo seats in one body. Longer life than either alone.
Maintenance-free top moulded sealOne moulded seal in place of a packing line. Zero atmospheric leakage.
Thickest knife on the marketMachined shear tip. Longer life, firmer shearing, at any pressure.
Clear conduit on open positionOpen position fully clear. High flow, very low pressure loss.
Interchangeable actuation on ISO 5210Actuators swap with the valve in the line.

Material options per component

ComponentStandardOptional
BodyGJS-500 ductile ironCF8M (316)
KnifeSS304SS316, Duplex, 17-4 PH
SleeveEPDMPU, NBR, NR, AFLAS
Front supportCarbon steelSS304
Top moulded sealEPDMPU, NBR, NR, AFLAS
Top plateCarbon steelSS304
StemSS304SS304
BridgeCarbon steelSS304
Coupling nutBrassBrass
Friction washerBrassBrass
HandwheelIronIron
Protection tubeCarbon steelCarbon steel
Blind cupPVCPVC

Epoxy coating on carbon steel components. Special materials and treatments on request.

Flange drilling summary

VariantANSI classMetric drilling
CORE SClass 150EN 1092 PN10
CORE CTo the dutyTo the duty

Flange drillings to most standards. Maximum working pressure does not exceed the rating of the selected flange drilling.

Available actuators

Actuator typeSize rangePower source
Handwheel (direct)Through 24”Manual
GearboxConsult ArnettManual
ElectricConsult ArnettElectric
Pneumatic cylinder (double-acting)Through 24”Compressed air
Hydraulic cylinder (double-acting)Consult ArnettHydraulic

Actuators interchange on a common ISO 5210 pad with the valve in the line. Other actuation options on request. Rising or non-rising stem. On/off service.

Actuator on the valve

Applications

Mining and mineral processing
CORE S valve
CORE S valve

Unidirectional knife gate

The seat comes out, the valve stays in.

232 psi to 8” | 2” to 24” | ANSI Class 150 | Unidirectional

The seat is a spare part

The snap-in soft seat sleeve is replaced by the site crew with the valve in the line. A worn seat becomes a scheduled task and the valve stays where it is.

Metal behind the soft seat

A fully machined metal seat sits behind the sleeve and holds the geometry, which is what gives the pairing a longer service life than a soft seat alone.

One seal in place of a packing line

The moulded top seal closes the gate to the atmosphere, in gas and high pressure water service alike. Maintenance-free by design.

Choose S valve when

Slurry isolation in one direction, a seat that the crew can change on site, and a duty inside the published pressure schedule.

CORE S technical data

Working pressure
58 psi to 232 psi
Sizes
2” to 24”
Face-to-face
1.7” to 6.1”
Flange drilling
EN 1092 PN10
ANSI 150
NPSFace-to-faceWorking pressure
2”1.7”232 psi
3”1.8”232 psi
4”2.0”232 psi
5”2.2”232 psi
6”2.2”232 psi
8”2.4”232 psi
10”2.7”145 psi
12”3.1”145 psi
14”3.1”58 psi
16”4.0”58 psi
18”4.5”58 psi
20”5.0”58 psi
24”6.1”58 psi

Special face-to-face on request. S valve dimensions. C valve is engineered to order to 1450 psi, with sizes and ratings quoted per project.

CORE C valve
CORE C valve

Extreme pressure knife gate

Built to the duty, up to 1450 psi.

To 1450 psi | Engineered to order | Unidirectional

Pressure beyond the standard range

CORE C carries the CORE sealing concept into duties above the published schedule, to 1450 psi. Every valve is engineered to the line it goes into.

The same seat principle

The metal seat and the soft seat sleeve carry over, so the maintenance routine a crew learns on CORE S applies here.

Choose CORE C when

Static head or pump discharge pressure sits above the CORE S schedule and the duty calls for a knife gate.

Choose the variant

CORE SCORE C
Working pressure232 psi to 8”, stepping down with sizeTo 1450 psi
Sizes2” to 24”Engineered to order
Face-to-face1.7” to 6.1”To the duty
Flange platformANSI Class 150, EN 1092 PN10To the duty
Shut-offUnidirectionalUnidirectional
CORE S series header
CORE S. Slurry isolation in one direction, a seat that the crew can change on site, and a duty inside the published pressure schedule.
CORE C series header
CORE C. Built to the duty, up to 1450 psi.
CORE S valve at the variant comparison
CORE C valve at the variant comparison

Contact Arnett

Call, send an email or fill in the form. An Arnett engineer replies with a quote and a recommended model.