HALO fully lined knife gate valves
HALO series

Fully lined knife gate valves

Max pressure
290 PSI
Pressure
Max temperature
435°F
Temperature
Sizes
2” - 24”
Sizes
Face-to-face
1.9” - 5.5”
Face-to-face
HALO S series header
LINED KNIFE GATE VALVE
HALO S valve
HALO H series header
HIGH PRESSURE LINED KNIFE GATE VALVE
HALO H valve

Lined valves

The Arnett Valve HALO series puts a one-piece liner across the whole wetted path. The media meets the liner and the gate, and the pressure envelope stays behind them. Every closing stroke flushes the sleeve groove clean.

Exploded view of the HALO valve
Self-flushing full-port designThe closing knife clears the groove. Settling media seals tight.
One-piece polyurethane linerThe wetted path is a replaceable part, changed on site.
True bidirectional zero-leak shut-offDrop-tight both ways, seat proven at 1.1x each way.
Zero atmospheric leakageThe media stays in the line and the floor stays dry.
Self-gasketing flange sealThe liner faces are the gaskets. Bolt in, both joints made.
Interchangeable actuation on ISO 5210Actuators swap with the valve in the line.

Material options per component

ComponentStandardOptional
BodyGJS500 ductile ironWCB carbon steel, CF8M (316)
Knife / GateSS31617-4 PH, Duplex, Super duplex
Sleeve / LinerPU polyurethaneNR, NBR, EPDM, FKM Viton, AFLAS
Top SealPU polyurethaneEPDM, NR, FKM Viton, AFLAS
ShaftSS316SS410, Duplex
Stem NutBronze–
FastenersA2/70 (304 stainless)A4/70 (316 stainless)
Protection PlatePTFECarbon steel, SS304, SS316

Others on request. The one-piece liner seals the full envelope, bottom joint included.

Temperature rating

Valve temperature rating is set by the sleeve compound. Select the compound, set the rating.

Sleeve compoundContinuous serviceBest for
PU polyurethane (standard)-30°F to 175°FSharp-particle abrasion, fine solids
NR natural rubber-40°F to 194°FAbrasion, impact, wet slurry
NBR nitrile-22°F to 212°FOily and fatty media
EPDM-40°F to 275°FHot water, dilute chemicals
FKM Viton-15°F to 392°FHigh temperature, aggressive chemicals
AFLAS+25°F to 435°FHigh temperature plus hot amines, steam

Design and face-to-face per MSS SP-81. Handles abrasive and corrosive slurries to 70% solids by weight. Hydrostatic test per API 598, shell at 1.5x and seat at 1.1x design pressure, both directions. Leakage class VI.

Available actuators

Actuator typeSize rangePower source
Handwheel (direct)2”- 6”Manual
Bevel Gearbox6” and aboveManual
ElectricStandard through 24”. Larger sizes per project.Electric
Pneumatic cylinder (single-acting)2” - 16”, custom, consult ArnettCompressed air
Pneumatic cylinder (double-acting)Standard through 24”. Larger sizes per project.Compressed air
Hydraulic cylinderStandard through 24”. Larger sizes per project.Hydraulic
Chain wheel2”- 6”Manual
Actuator on the valve

Applications

Mining and mineral processing
HALO S valve
HALO S valve

Standard lined knife gate valve

The lined workhorse of the HALO series.

145 psi | 2” to 24” | ANSI Class 150 | Bidirectional drop-tight

Complete lined protection

The one-piece polyurethane liner shields the entire wetted path across the full size range. The media meets the liner and the gate, and the pressure envelope stays protected behind them.

Broadest chemistry range in the catalog

Food processing, chemical processing and desalination sit alongside the classic mining duties. Where corrosion or contamination rules apply, HALO S stays in.

Self-flushing full port

The closing knife accelerates flow through the sleeve groove and clears it on every stroke. Settling and scaling media seal drop-tight on the valve's own action.

Choose HALO S when

Abrasive or corrosive slurry isolation to 24”, food or chemical compatibility requirements, media that settles or scales in conventional knife gates.

HALO S technical data

Working pressure
145 psi to 24”
Sizes
2” to 24”
Face-to-face
1.9” to 4.5”
Flange drilling
EN 1092 PN10
ANSI 150
NPSFace-to-faceOverall heightISO 5210
2”1.9”10.2”F07
2-1/2” *1.9”––
3”2.0”12.2”F07
4”2.0”13.4”F07
5” *2.2”––
6”2.2”16.9”F07
8”2.8”20.9”F10
10”2.8”23.4”F10
12”3.0”28.0”F10
14”3.0”31.5”F10-F14
16”3.5”34.8”F10-F14
18”3.5”38.6”F10-F14
20”4.5”41.7”F14-F16
24”4.5”48.0”F14-F16

* = made to order (2-1/2” and 5”). Overall height, ISO 5210 and drilling published for standard sizes. Overall height is the bare shaft configuration. Custom flange drilling to fit any requirement. PN16 and AS 2129 Table D and E available. Hydrostatic test per API 598, shell at 1.5x and seat at 1.1x design pressure, both directions.

HALO H valve
HALO H valve

High pressure lined knife gate valve

Same envelope, two and a half times the pressure.

290 psi | 2” to 24” | ANSI Class 150 | Bidirectional drop-tight

Reinforced pressure envelope

Thicker body sections and a heavier lay length carry the working pressure above the HALO S rating with the same one-piece liner and the same self-flushing geometry.

Matched flange platform

Drilled for ANSI Class 150, with EN 1092 PN25 for metric installations. The valve matches the flange class the line already carries.

The same wear part

The liner remains the only consumable. Higher pressure service on the same spares list and the same maintenance procedures.

Choose HALO H when

Discharge lines, cyclone feed, higher static head, or any lined-valve duty above the HALO S rating, with the media and maintenance profile carrying straight over.

HALO H technical data

Working pressure
290 psi to 24”
Sizes
2” to 16”
Face-to-face
1.9” to 5.5”
Flange drilling
EN 1092 PN25
ANSI 150
NPSFace-to-faceOverall heightISO 5210
2”1.9”11.0”F07
3”2.5”13.4”F07
4”2.5”14.6”F07
6”3.0”18.9”F10
8”3.5”22.8”F10
10”4.5”25.4”F14
12”4.5”31.1”F16
14”5.0”35.0”F16
16”5.5”39.0”F16

Overall height is the bare shaft configuration. Custom flange drilling to fit any requirement. PN16 and AS 2129 Table E available. Hydrostatic test per API 598, shell at 1.5x and seat at 1.1x design pressure, both directions.

Choose the variant

HALO SHALO H
Working pressure145 psi290 psi
Sizes2” to 24”2” to 16”, larger to 24” on request
Face-to-face1.9” to 4.5”1.9” to 5.5”
Overall height at 16”34.8”39.0”
Flange platformANSI Class 150ANSI Class 150
Shut-offBidirectional drop-tightBidirectional drop-tight
HALO S series header
HALO S. Abrasive or corrosive slurry isolation to 24”, food or chemical compatibility requirements, media that settles or scales in conventional knife gates.
HALO S valve
HALO H series header
HALO H. Discharge lines, cyclone feed, higher static head, or any lined-valve duty above the HALO S rating, with the media and maintenance profile carrying straight over.
HALO H valve

Contact Arnett

Call, send an email or fill in the form. An Arnett engineer replies with a quote and a recommended model.