OMNI bidirectional knife gate valve
OMNI series

Bidirectional knife gate valves

Max pressure
145 PSI
Pressure
Max temperature
392°F
Temperature
Sizes
2” - 24”
Sizes
Face-to-face
1.7” - 6.1”
Face-to-face
OMNI S series header
Bidirectional knife gate valve
OMNI S valve

Bidirectional valve

The Arnett Valve OMNI series seals with the pressure on either face, as standard. The bore is full and the body floor is clear, so media passes through on every stroke instead of settling. A single moulded top seal closes the gate to the atmosphere.

Exploded view of the OMNI valve
Maintenance-free top moulded seal One moulded seal in place of a packing line. Zero atmospheric leakage.
Zero-pocket cavity A clear body floor. The valve flushes itself on every stroke.
O-ring profile seal Machined groove, o-ring profile. Tight both ways, seal shielded from the media.
Thickest knife on the market Machined shear tip. Longer life, firmer shearing, at any pressure.
Clear conduit on open position Open position fully clear. High flow, very low pressure loss.
Interchangeable actuation on ISO 5210 Actuators swap with the valve in the line.

Material options per component

Section detail, shared parts
ComponentStandardOptional
BodyGJS500 ductile ironCF8M (316), SS316, Duplex, 17-4 PH
Knife / gateSS304–
Front supportCarbon steelSS304
Top moulded sealEPDMPU, NBR, NR, AFLAS
Top plateCarbon steelSS304
Stem–SS304
BridgeCarbon steelSS304
Coupling nutBrassBrass
Friction washerBrassBrass
HandwheelIronIron
D/A pneumatic cylinderDuctile iron and compositeDuctile iron and composite
Blind cupPVCPVC
SealEPDMPU, NBR, NR, AFLAS

Epoxy coating on carbon steel components. Special materials and treatments on request.

Flange drilling summary

VariantANSI classMetric drilling
OMNI SClass 150EN 1092

Flange drillings to most standards. Maximum working pressure does not exceed the rating of the selected flange drilling.

Working temperature

392°F standard working temperature
Temperature range graphic

Available actuators

Actuator typeSize rangePower source
Handwheel (direct)Through 24”Manual
GearboxConsult ArnettManual
ElectricConsult ArnettElectric
Pneumatic cylinder (double-acting)Through 24”Compressed air
Hydraulic cylinder (double-acting)Consult ArnettHydraulic

Actuators interchange on a common ISO 5210 pad with the valve in the line. Other actuation options on request. Rising or non-rising stem. On/off service.

Actuator on the valve

Applications

Mining & minerals
OMNI S valve
OMNI S valve

Bidirectional knife gate valve

Drop-tight from either side, on a bore that clears itself.

145 psi to 12”  |  2” to 24”  |  ANSI Class 150  |  Bidirectional drop-tight

Sealed from either side

The side seal sits in a machined groove with an o-ring profile. It holds with the pressure on either face and the media stays off the seal.

A floor that clears itself

The body has a flat, clear floor. Every closing stroke pushes settled media through, so the seal meets a clean seat each time.

One seal in place of a packing line

The moulded top seal closes the gate to the atmosphere, in gas and high pressure water service alike. Maintenance-free by design.

Choose OMNI S when

Slurry isolation with pressure from either side, settled solids that would foul a conventional seat, and a packing gland the crew is tired of repacking.

OMNI S technical data

Working pressure
145 psi to 12”
58 psi to 24”
Sizes
2” to 24”
Face-to-face
1.7” to 6.1”
special on request
Flange drilling
EN 1092
ANSI 150
NPSFace-to-faceWorking pressure
2”1.7”145 psi
3”1.8”145 psi
4”2.0”145 psi
5”2.2”145 psi
6”2.2”145 psi
8”2.4”145 psi
10”2.7”145 psi
12”3.1”145 psi
14”3.1”58 psi
16”4.0”58 psi
18”4.5”58 psi
20”5.0”58 psi
24”6.1”58 psi

Special face-to-face on request. Working temperature up to 392°F.

Contact Arnett

Call, send an email or fill in the form. An Arnett engineer replies with a quote and a recommended model.